Mulja tv repair portal

Equipment Repairs => LCD TV forum => Topic started by: Hornnumb2 on February 13, 2019,17:42:30

Title: sharp lc-60le640u Backlight but no video or sound.
Post by: Hornnumb2 on February 13, 2019,17:42:30

Working on this unit, I have check voltage to main board and are getting the 13 & 3 and 5 volts. I have check voltage to t con board and get 12v on first 2 and zero on last 2 pins. The unit does power on and has backlight but no Video or sound. I was just getting backlight but I have messed with ribbon cables on t con board and now I get some red lines on left side of screen.

Title: Re: sharp lc-60le640u Backlight but no video or sound.
Post by: downunder on February 14, 2019,02:36:05

See if your problem is per attachment. The 2 flat white flexies at the bottom of your picture - are these what you messed with?


Clean the contacts on these and make sure they're seated properly in the sockets, especially the one on the right.                      Bruce

Title: Re: sharp lc-60le640u Backlight but no video or sound.
Post by: Hornnumb2 on February 15, 2019,10:43:25

I did test the panel by removing one ribbon at a time. half screen white and other black and vice versa. So I think that shows the panel is good right? I just get backlight but no video or menus. The green light flashes on the main board should it be constant? Thanks

Title: Re: sharp lc-60le640u Backlight but no video or sound.
Post by: Hornnumb2 on February 15, 2019,22:05:19

Replaced t-con for no change except to clear up the red line I caused, back to backlight but nothing else. I got some more reading from top of powerboard.
1- 12.1v. PNL 12v
3- -.009 GND
5- 13.1v UR 13.2v
7- 13.1v. UR 13.2v
9- .010. GND
11- .010. GND
13- 3.31v. AC_DET
15- 5.04v. BU 5v
17- 1.15v. PWM1
19- 1.3v. Dimmer
21- 1.15v. OFL
23- .000v. PWM2

Any suggestions from that, I can check the readings on the bottom if needed. I am not sure about 17 and 23. Thanks

Title: Re: sharp lc-60le640u Backlight but no video or sound.
Post by: downunder on February 16, 2019,04:11:34

Those voltages are all normal. PWM1/2 are to do with the backlights which you say are on. T-con has been changed. Can't see the power supply causing it.

So it's starting to look like main board. I'll upload the service manual to quuq.  Bruce

Title: Re: sharp lc-60le640u Backlight but no video or sound.
Post by: Hornnumb2 on February 16, 2019,22:40:03

Thanks Bruce, main board on way.

Title: Re: sharp lc-60le640u Backlight but no video or sound.
Post by: Hornnumb2 on February 19, 2019,22:27:34

Well installed main board today with no change, I have a shop jimmy kit to rebuild power supply. I just know where to go from here. Thanks Michael

Title: Re: sharp lc-60le640u Backlight but no video or sound.
Post by: downunder on February 20, 2019,02:41:01

OUCH! bum steer - sorry about that Michael, but that's the way of it in this industry. Ah well, soldier on.                       Bruce

Title: Re: sharp lc-60le640u Backlight but no video or sound.
Post by: Hornnumb2 on February 20, 2019,15:06:00

Any next step to take?