Mulja tv repair portal
Spares => Spares for sale => Topic started by: davenjax on October 12, 2010,12:51:19
-
tcon/psu/inverter for sale sony panasonic vestel various available just message or inbox what you require
-
Hi Dave,
Bet you don't have a BN96-03775A ? - Chris.
-
hi chris i was way ahead of you i already checked to see if i could help but to no avail im afraid apologies .just stripped a nice panasonic with a very attractive psu ill try and get a piccy on
-
Hi, D/J,
Seems a bit wicked, only like smooth Sammies, but - will go for it, this time - Chris
-
tcon/psu/inverter for sale sony panasonic vestel various available just message or inbox what you require
Hi do you have a working psu 17pw20v1 vestel board? Best Price?
regards
-
hi sorry i have a few vestel psu up to 17pw26.1 but not what you require apologies rgds dave
-
Hi again Dave,
Confess have so much stuff from local recycling depots, wouldn't dare advertise it. However if folks state their requirements on 'things wanted' section, will check stocks and reply, fairly niftily - panels all labelled and piccied - need to be retired, for the time it takes - Chris.
-
understood chris cant get near the recyclin place down our end they be tighter than a knats chuff .rgds dave
-
Hi, Dave,
But do you mend thier tellies -
They tend to have more wives and G/F than telly mending chaps ever manage - and with all those tellies to mend for all those offspring, onnspring and such.
Telly menders never had it so good, but at least a quiet life, these-days - doesn't seem fair - Chris.
-
hi chris to be given even a chance to look at the tvs they get in would be a start but alas to no avail .ps had a profilio psu bounce on me .bloody thing .rgds dave
-
Hi Dave,
It's those rubbish caps you use - was amazed to find that PT originals lasted a couple of years, and my Wiltsgrove specials more like a month. Tried various combinations then noticed Wilts does a super low ESR 2200/16 - been a fortnight used lots and not a failure yet.
As to recycling, guess there's lots'a cash in flat screen stuff - chaps used to be able to 'tot' the stuff then health and safety fell over one, now they end up on Ebay. Trouble is, at local sites they use a machine with rotating spikes to compress the electronics in the skip before recycling - makes a mess of the screens though.
-
well when i get it back from the customer with a red face ill look over caps again if to no avail sod the bloody thing. ps spares may be available watch this space lol .dave
-
Hi Dave,
If it's one like the piccy, will almost bite yer arm off - well it was my first LCD repair - cust had been on the interweb and changed all the caps for 85deg stuff - some drooled down the board and phutted the primary side.
Changed everything imaginable - Have pages of my sorrows - got 5v S/by and 24v to go but could never revive the 12v side. Set remains in the loft like a beached albatross (Profilos have little style) - haven't the heart yet to recycle with a hammer - Chris.
-
HI!
Wanted to ask if you have a t-con V32B C3 - QD32HL01 (or QD32HL02) for LG PHILIPS (32PF3320) LCD?
Regards.
-
hi yes i have this panel did you want to send a photo of yours so i can compare ? otherwise 12.00 plus postage rgds david
-
hi there, i'm after a 17pw26-3?? best price?
-
how about a LVDS BOARD 320AP03C2LV0.2 samsung?
-
hi
do you have an ipos 150 rev1.8 psu from a bush idlcd32tv16hd. if not, would you have any idea where i could locate a 3.15a 250v fuse for this board. it is located on the board at f2, and is covered in green rubber.
regards
john
-
hi mate if its a standard glass fuse you should be able to locate via ebay or ohm supplies i have worked on this board but never had a blown fuse always been the caps that need replacing still cheap and easy enough to do if it is the fuse there will be a letter before the rating ie t or f make sure you get the correct type .dave .ps usualy there are 2 caps close to the center top that will be bulging from the top. change them
-
hi
thanks for your reply.
you are right, the two caps you mention had bulged, so i did replace them but tv still only has sound, no picture.
after much searching, i found a thread where someone had the exact same problem, and after he replaced caps he found this fuse had blown. After replacing fuse tv worked again.
the fuse in question is an axial fuse, coated in a green rubber sleeve locate at f2 on the board.
after i desoldered the fuse and circuit tested it i got no reading.
the tv sound still works with this fuse removed.
the only fuse i can find with the same ratings are radial fuses from rss, but i am not sure if these would be a good substitute.
john
-
hi john i do have another ipos power supply slightly different to the one your working on i will have a look for the fuse and desolder for you if it has one .also i have had an issue where by the backlight inverters sometimes cut out after a few minutes and come back on again than off and on and so on if this happens you will need to change all the caps including the ones under the heat sinks the far right heat sink has two small caps cant remember the values off hand but they are important for the cure ...ill get back to you .dave
-
cheers dave
any and all help greatly appreciated. the back light does not seem to be lit, I assumed this was caused by the missing fuse.
john
-
hi john im sorry but the fuse i have is 6.3a from a larger set no doubt however found a good replacement at newark.com/littelfuse i just tapped in 3a axial in the search bar and that site seemed to have the best replacement unfortunatly its in the states but will probably ship to the uk will just take longer your welcome to my 6.3 just to see if the set fires up if you like cant be much more help im afraid :c023:
-
no worries dave, i'm grateful for the time you have already taken just to talk and try to help. dont want to risk a fuse with double the rating in case there is another fault that caused the fuse to blow.
think i will order a couple of radial fuses from rss just to see if the set does now fire up.
will post an update of how i got on.
thanks
john
-
no probs mate good luck and please post back would be good to hear a positive result .dave
-
do you have vestel 17mp12-3 main board require for techwood 26 inch model
astracat
-
hi sorry i only have 17mb15-3 rgds dave