Mulja tv repair portal
Equipment Repairs => PLASMA TV forum => Topic started by: timtamtimtam on March 26, 2011,20:15:48
-
My th-50phw3 shuted down sometimes automatically when I was watching TV during past 2 months. but now it can't be turned on.
Problem: http://www.youtube.com/watch?v=bufQiahAPkc
It goes to green light, fans work and system sound likes power turn on around 2 secs after switch on the power. Red is light and system sound likes power cut off then turns red blinking 2-3 times a few seconds later.
I've founded the service manual for th-50phw3 GPH3D, it shows the self test on page 29 and troubleshooting guide on page 30.
service manual: http://www.sendspace.com/file/hmm1bl
troubleshooting guide (half page): http://www.youtube.com/watch?v=Met4gPofds0
I've followed the self check and troubleshooting guide. However, I get stuck in self check and the part of "removing P7 board" in troubleshooting, I've no ideas how to find out which board is defective.
self check: http://www.youtube.com/watch?v=tVSktmjJ_gQ
It goes to green light and fans work around 2 secs after swith on the power. Then red light is on but no blinking (like standby mode). However, it goes red light blinking 2-3 times after I turn on the power by using remote control.
Does anyone can tell why can't go to the self check and it looks like go to the standby mode? :sign0085:
Remove p6: http://www.youtube.com/watch?v=xU472EdIbOg
It goes something difference. red light blinking a bit longer (3-4 times) and no fan and system turn on after remove P6 board.
Does anyone can tell what's happen and why the blinking is longer? :sign0085:
It looks funny and strange becuase the result of self check and result of removing p6 are never mentioned in the service manual.
Inserted back P6 and Remove p7 (assuming P6 works fine): http://www.youtube.com/watch?v=LWTe9ktYRPY
result same as the result at the beginning:
It goes to green light, fans work and system sound likes power turn on around 2 secs after swith on the power. Red is light and system sound likes power cut off then turns red blinking 2-3 times a few seconds later.
Remove p6 & p7: http://www.youtube.com/watch?v=fNXQg0PKzaY
Same as Remove P6
Please help and thanks a lot! :c017:
- Tim
-
Best to put it back together Tim, and count the blinks exactly, should be 2-3 blinks then pause, then blink code repeats. Should be fault code in service manual which will give you the PROBABLE faulty board.
-
Best to put it back together Tim, and count the blinks exactly, should be 2-3 blinks then pause, then blink code repeats. Should be fault code in service manual which will give you the PROBABLE faulty board.
Hi ozzie mate,
Really thanks for your reply :93:
I was an oversea student studying in melbourne and have been back to HK long time ago. It's so nice to meet you in here. :yahoo:
I tired to count the blinks exactly, but it quite difficult because it looks like a half blink at the first blink as you can see in the youtube video. It should -1 blink if I have to tell the blink exactly. for example 2-3 blinks, shoulb be 2 blinks, 3-4 blinks should be 3 blinks. On the other hand, I've also found out and take a look at other different series of panasonic plasma, such as GPH5D and higher, and I realize that GPH3D is the oldest out of all GPH series. There is no definition of blinks only in GPH3D. Also, no LED on any boards in GPH3D.
Would you mind to take a look at that service manual for a while and try to give me some hints? :17: :c017: I'm really sick of that GPH3D manual. :41:
Thank you so much! :13:
- Tim
-
You're right Tim, doesn't seem to be fault code for this model, and it is fairly old, so parts may be hard to find. If you're keen to have a go you need to start pulling plugs. Start with the power plugs on the sustain boards, one at a time, then try DG5 connector, even try disconnecting buffer boards one at a time. Very little info on this model.