Mulja tv repair portal
Equipment Repairs => LCD TV forum => Topic started by: Turnip on September 25, 2011,08:10:09
-
Hi folks,
Have one of these that makes the usual start up Fa/Da - screen briefly lights with OSG then nothing, not even the S/by led. Set appears to be in sulk mode and ignors control. PS voltages remain at 5V and 15V.
Guess it might be in the inverter area but transformer secondary ohms are identical and caps look OK.
Any thoughts ? - Thanks - Chris.
-
hi
chris got one the same did you manage to cure the fault
or did you change the psu/inverter
dave
-
Hi Dave,
Couldn't find any bits so gifted by cust and on the heap pending - Chris.
-
Hi Chris ..
Recognise that invertor transformer ...and is known to be a troublemaker ..
Had a few burn/arc internally..but read ok cold
In the old days I would quote for a new pcb ..
but ..I think CHS now stock the transformer on its own ..
rgds
Evan
-
hi
chris do you still have panel if so could do with inverter
transformer
thanks dave
-
Hi Dave,
Our Evan doesn't yet give order details - hanging on to that panel/set for the retirement pound - Note that ChasHyde seems to have the the tranny - Chris
-
Hi Dave,
Our Evan doesn't yet give order details - hanging on to that panel/set for the retirement pound - Note that ChasHyde seems to have the the tranny - Chris
Sorry Chris ...
Didn't have a scrap board to hand to reference the transformer number ..
All I could remember ...top of the head...was that I recognised the transformer and had previously obtained one from CHS (ChasHyde)..
rgds
Evan
-
Wicked - Evan,
Some old folks have nothing better to do but to try get details.
Must get a secondary life of sorts, but as a humanist - still rather doubtful - Chris
-
hi
chris chs only supply on psu/inverter panel not on there own
dave
-
I can only appologise ...
I had it confused with this chappy
CHS pt no :- 3547177
Thats what comes of not having a panel in front of me to look at..
Chances are a special order enquiry with Jo at CHS will get results ..
The one I was thinking of was cheap enough ...but as I now realise ...is different to yours.
Sorry Chris
Evan
-
hi
look on chris pic nothing like that have
that in stock for for this model
dave
-
hi
look on chris pic nothing like that have
that in stock for for this model
dave
As I said ..I appologise for getting his hopes up ..
I honestly thought I recognised the transformer ..
Since I didn't actually have a board in front of me ...I just assumed... wrongly I admit...they were one and the same.
It is well over 6 months since I saw one ...and my memory ain't as sharp as it once was.
had to do some digging on past CHS orders to come up with the one I thought it was ...and the photo.
In future I'll keep my gob shut ..unless I'm 100%
;)
rgds
Evan
-
hi
thanks for looking
dave
-
Hi Dave,
Note that some of these trannies are pin similar - some are even cheap. Haven't yet checked secondary resistance of my Sammy, but bet as you have one, you have.
Have a small pile of NYD741FC - fits Samsung LS 22TDVSUV/EN (4 tube set) 700 Ohm dual secondaries.
Just a thought - Chris
-
hi
chris ordered new panel
dave
-
Hi, Dave,
Wot - no secondary resistance info, and you always unhappy about Quuq non-info - no gong for you, quite yet, I guess - Chris
-
ih
its prob not inverter transformer thats causing the fault
borrowed transformer still no backlite so tried
borrowed psu/inverter pcb with my transformer fitted
works ,put in original pcb faulty
got new panel coming at a very good price
dave
-
hi
chris
FAULT CURED BY REPLACING INVERTER/PSU WITH NEW PANEL
DAVE
-
hi
chris posted cured ok
dave