Mulja tv repair portal

Equipment Repairs => LCD TV forum => Topic started by: mike r sharp on May 31, 2008,16:44:34

Title: Sharp Aquos stanby light
Post by: mike r sharp on May 31, 2008,16:44:34

I have a Sharp Aquos lcd about 3urs old it turned itself off.The sound came back on with the remote then it too went off.The remote batteries are new.The nearest service center is in Honolulu and it will cost$100 =for shipping/ins. as well as $100 for shop charge + repair cost.I am not sure if it is worth it,a new version of the tv is at Costco for under$600.I am handy with tools and have worked on electronics before,the set is not under warranty and is just collecting dust.Any suggestions? Mike

Title: Re: Sharp Aquos stanby light
Post by: steph. on June 01, 2008,16:09:04

Unfortunately m8 I have the exact fault in my workshop. Been in contact with other servce engineers and all, including me, agree that it should be binned, unless you want to pay that sort of money for a repair.

See Sharp Aquos post below, submitted by steph., below.

Sorry!!

Title: Re: Sharp Aquos stanby light
Post by: BC109 on June 01, 2008,21:34:30

What model number is it?
Some Sharp will lock up if protection is detected a number of times.
If the unit detects a lamp (ccfl) error 5 times it locks up & red LED comes on. Resetting uPC error may get it going again.

Of cause you may have a completely different fault.

Title: Re: Sharp Aquos stanby light
Post by: steph. on June 02, 2008,15:49:13

The model number for this Sharp Aquos tv is LC-32P5OE.

Any help would be appreciated with this fault.

Title: Re: Sharp Aquos stanby light
Post by: lubos55 on June 03, 2008,02:47:47

Quote from: steph. on June 02, 2008,15:49:13

The model number for this Sharp Aquos tv is LC-32P5OE.

Any help would be appreciated with this fault.

Hi,

is model LC-32P5OE correct info,or LC-32P50E is OK???Check attach.please.I have full manual.If you need I will send it.

Title: Re: Sharp Aquos stanby light
Post by: BC109 on June 03, 2008,07:18:18

I dont have that manual but you need to enter service mode and reset error data is one method. See if this works
Off at mains.Press & hold [input] & [vol-] on panel & power on at mains.TV comes on in [K] mode.Simultaneously press [vol-] & [Pr-] on panel & the Adjustment Process Mode will appear.On bottom line check if ERROR NO: RESET reads 1 or more.If so, the Lamp Detection was executed.Select bottom line & use [vol+] or [vol-] to reset to zero.

But if you get the service manual it should help. Some need options to be reset like model number (4:3) 16:9 models etc, due to data corruption.
Hope that helps
 

Title: Re: Sharp Aquos stanby light
Post by: tv tony on June 03, 2008,11:35:31

hi, u require full service manual plus faultfinding flow chart, (for what the flow charts are worth)?
let me know as asap. ill mail them to you, regards, tony walker

Title: Re: Sharp Aquos stanby light
Post by: lubos55 on June 20, 2008,11:26:18

Quote from: tv tony on June 03, 2008,11:35:31

hi, u require full service manual plus faultfinding flow chart, (for what the flow charts are worth)?
let me know as asap. ill mail them to you, regards, tony walker

Hi,
if you need this manual please send require on my email, see my profile.

Title: Re: Sharp Aquos stanby light
Post by: badrick on June 21, 2008,18:17:54

you could try checking lamp wires as they can sort on the metal work in side the screen see link attached.
andy