Mulja tv repair portal

Equipment Repairs => LCD TV forum => Topic started by: GP ELECTRO on November 27, 2009,11:22:23

Title: Diagram for power board for BEKO(or BUSH) LM chassis
Post by: GP ELECTRO on November 27, 2009,11:22:23
Hello my friends,
please if someone has schematic diagram of Power supply board for BEKO LM chassis to upload it.

The name of power board is : FSP204-2F01(S07)

Many thanks in advance for help and support
Peter
Title: Re: Diagram for power board for BEKO(or BUSH) LM chassis
Post by: Turnip on November 27, 2009,13:19:17
Hi Peter,

Have a pic - what's your problem - Chris.
Title: Re: Diagram for power board for BEKO(or BUSH) LM chassis
Post by: GP ELECTRO on November 27, 2009,14:13:00
Hello Chris,
the unit come total dead.When I have opened the TV set I have found two defect elcos(CS13 1000mF/25V & CS20 470mF ) after replacement LCD TV works perfect about 5-6 hours.It was night and I switched of the unit and go home.Tomorrow when I come in service I want to check the unit again and switched on it - but it's don't work more. Power board was dead (nothing was burned ,everything on firs look looks OK-but it stop working)
I think that maybe some resistor in primary side change his value,but I am not sure maybe I have no right.
On the main elko there is 300V and on the secondary side is nothing.I cannot see the mark of IC1 which is primary side.Around this IC are 3 transistor and 3 diode -they are OK.
Therefore I need the diagram of this board to try to find where can be the defect to try to fix it.
Chris if you have more experience with this board can you send me some sugestions
Many thanks in advance for support and help.
Regards
Peter
Title: Re: Diagram for power board for BEKO(or BUSH) LM chassis
Post by: GGTVBD on November 28, 2009,03:51:28
Try changing C13, C15 and C26.

I'd replace all of them though.
Title: Re: Diagram for power board for BEKO(or BUSH) LM chassis
Post by: GP ELECTRO on November 28, 2009,04:33:15
Hello GGTVBD,
C26 I have replaced,other twoo i have replaced before.Now board works partial.I have 12V on connector CN2 but on connector CN3 there are no voltage.I have changed the IC in chopper 1207 (IC's is OK).
It is very simply chopper but without diagram it is not easy to find the defect
Title: Re: Diagram for power board for BEKO(or BUSH) LM chassis
Post by: Turnip on November 28, 2009,12:35:43
Hi GP Electro,

Can't help with shematic or likely solution.  Power supply picture I supplied (FSP204-2F01 (SO7)) came from a smashed screen Beko 26WLB520HD, but PS works OK.

If interested - Email - Chris.
Title: Re: Diagram for power board for BEKO(or BUSH) LM chassis
Post by: Κώστας on November 28, 2009,14:17:14
Download diagram  here. (http://www.tv.quuq.org/index.php?ind=downloads&op=entry_view&iden=287")
Title: Re: Diagram for power board for BEKO(or BUSH) LM chassis
Post by: celltrix on April 10, 2016,17:42:24
 :oops: :sign0085: :sign0085:
hi guyz i treid to download this service manual..but get an error could anyone please mail it to me my email is sbu@live.co.za
thank you in advance...
Title: Re: Diagram for power board for BEKO(or BUSH) LM chassis
Post by: jordan on April 11, 2016,03:29:00
http://elektrotanya.com/grundig_lxw686612ref_beko_lm_chassis_lcd_tv_circuit.pdf/download.html