Author Topic: Philips DVDR5520 - No go.  (Read 140 times)

0 Members and 1 Guest are viewing this topic.

Turnip

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3470
    • Email
Philips DVDR5520 - No go.
« on: May 12, 2019,12:14:33 »
Hi folks

Just had one in for no go. Primary seemed OK, start up chip resistors in value, just no secondary voltages. Took the power board out where the main cap bit me. Secondary had 2 x 3300 mfd 10v caps looking distressed, so replaced them.

Surprisingly it fired up with no issues whatever - Just needed a re-scan. Pretty good for a 2008 machine - Chris.

Mulja tv repair portal

Philips DVDR5520 - No go.
« on: May 12, 2019,12:14:33 »

downunder

  • Hero Member
  • *****
  • Posts: 1014
Re: Philips DVDR5520 - No go.
« Reply #1 on: May 12, 2019,21:10:54 »

Thanks for the heads-up, Chris.               Bruce

Turnip

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3470
    • Email
Re: Philips DVDR5520 - No go.
« Reply #2 on: May 13, 2019,12:31:58 »
Hi Bruce, yes well,

Have noticed 'Quuq' often pops up on a Google fault search, including quite a few of yours too - Chris.

Mulja tv repair portal

Re: Philips DVDR5520 - No go.
« Reply #2 on: May 13, 2019,12:31:58 »

downunder

  • Hero Member
  • *****
  • Posts: 1014
Re: Philips DVDR5520 - No go.
« Reply #3 on: May 14, 2019,03:10:43 »

So, we're giving the DIYers a leg up for free - forum should be members only, maybe.

Turnip

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3470
    • Email
Re: Philips DVDR5520 - No go.
« Reply #4 on: May 15, 2019,12:48:14 »
Hi Bruce,

Gather there are such forums for members only, even might know some members, perhaps, but they never pass on any info, as seems its death or a ban from such sites.

Great fun today as got a new'ish 'smart' Bush/Vestel with a genuine Vestel screen (Gather they formerly used LG where they died like flies)

The new Vestel screen is 'Cost Improved' with Leds 1.6mm square - Bit small, I thought, and with nothing to prevent folks pushing the screen in, if in the mind. Happily the strips clean up nicely with a glass fibre pencil, where a 50/50 3v diode does the biz. Bit worried about any guarantee as just done a third Led mend on a Panny using LG diodes in a year - Chris.

astracat

  • Hero Member
  • *****
  • Posts: 284
    • Email
re members only
« Reply #5 on: May 21, 2019,13:26:52 »
hi all
seen quite a few google search to this sight, a members only to qualified repairers  a good idea have c&g myself , if only to stop the odd idiots from killing themselves or doing a bad repair giving this trade a bad reputation , 
regards
astracat

Mulja tv repair portal

re members only
« Reply #5 on: May 21, 2019,13:26:52 »

Turnip

  • Global Moderator
  • Hero Member
  • *****
  • Posts: 3470
    • Email
Re: Philips DVDR5520 - No go.
« Reply #6 on: May 25, 2019,12:55:39 »
Hi Astracat,

Got my C&G with wind-up gramophones, where spring repair was life threatening. We just wound 'em out, and when we got to the middle where the break was - We heated the spring and sorted it with 'Woolworth' drills in a hand-brace as all available.

After a week or two, we broke through, and sorted suitable nails, then hammered them flat.

Winding back in was an issue, as any slip detached one's head

Happy to say, my elder brother at 84 seems to have survived. Was dubious myself, but elder brothers advice shouldn't be ignored.

Must admit however that he said that a bumble bee wouldn't sting if grasped

Bugger did - Became dubious at seven - Chris.

astracat

  • Hero Member
  • *****
  • Posts: 284
    • Email
Re: Philips DVDR5520 - No go.
« Reply #7 on: Today at 14:41:48 »
hi turnip
did my training around 69 remember watching moon landing on b&w telly on bench where pl509 s used bite if you got too close to anode cap
,used to enjoy sneakly watching bbc2 trailer films like the aussy road trains
regards
astracat

 

Powered by EzPortal
download