Author Topic: PHILIPS FTR9965 RECEIVER BOX (Read 11936 times)

brian · « **on:** November 03, 2008,16:08:44 »

Hi;
As anyone got a service manual?,for this box. the fault is as follows,
The display panel is working o.k. but the receiver powers on,with
picture and sound for a few seconds,then picture breaks up into lines and the box switches back into standby!
On entering sam, no error codes are present, have replaced all electrolytics in power supply. Very rarely box will run ok! till switched off and back on then fault returns.
Many Thanks
Bri.

Mulja tv repair portal · « **on:** November 03, 2008,16:08:44 »

BC109 · « **Reply #1 on:** November 04, 2008,00:16:48 »

Do you have model & chassis number of panel/TV?

brian · « **Reply #2 on:** November 04, 2008,07:26:38 »

Hi BC109
The model is 42FD9944/01S
CHASSIS IS FM24
THANKS ,
BRI.

Mulja tv repair portal · « **Reply #2 on:** November 04, 2008,07:26:38 »

brian · « **Reply #3 on:** November 04, 2008,12:01:00 »

Hello, AgainMore info. By entering the box SAM, as opposed to the PDP,SAM!,Have found the following:ERROR CODES.066053077050000DEFECTIVE MODULE +3V (Fbx) SUPPLY.Have also found that by changing to a "stand alone"option the box will work o.k.!!Puzzled?Thanks AgainBRI.

brian · « **Reply #4 on:** November 04, 2008,12:02:53 »

Hi,
That should read
066,053,077,050,000
Cheers
Bri.

BC109 · « **Reply #5 on:** November 04, 2008,21:28:05 »

:ciao:

Mulja tv repair portal · « **Reply #5 on:** November 04, 2008,21:28:05 »

BC109 · « **Reply #6 on:** November 04, 2008,21:34:47 »

:dry:

BC109 · « **Reply #7 on:** November 04, 2008,21:36:45 »

:ciao:

BC109 · « **Reply #8 on:** November 04, 2008,21:39:40 »

I think this relates to your model.
Set turns on for ~10sec,no display, LED flashes red, then standby.
Low 3.3V & 5V rails trigger protection.

Rebuild power supply, 3.3v & 5V lines filter caps dry up.
I have found a few Philips plasma with different chassis all suffering similar problems. 3.3v & 5v filter caps.

Also check XSUS look for 2 SMD caps in the top right corner, C48 & C49 (10u each), replace.

Good luck

brian · « **Reply #9 on:** December 07, 2008,05:10:41 »

Hi,
Replaced all elect.caps. as advised. Also the caps in the media box p.s.
Everything now o.k.
Many thanks
Bri.

DAVIDTV · « **Reply #10 on:** December 23, 2008,06:01:39 »

My Philips 33FD9944/01S is now working having changed several electrolytic capacitors in the power supply. The television only as a VGA input and works well when connected to my computer. It is normally connected to a Philip FTR9964/12S receiver unit. If I connect a television to either External 1 or External 2 SCART and push the power button the following happens:
The power LED is red for an instant, the relay on the power supply energises. The power LED turns orange. After about 2 seconds the picture from the analogue tuner appears but without sound. The picture remains for about 6 seconds. The power LED turns green, almost immediately the relay de-energises and the power LED starts flashing.
I’ve checked all the electrolytic capacitors in the power supply in-situ with a Peak Atlas ESR meter and all appear to be satisfactory. I’ve also bridged each voltage output from the power supply in turn with a large capacitor. This made no difference. I’ve also tried a large capacitor across the input to the 3.3 volt regulator (7009) and a 47 mfd capacitor across its output, again with no change.
Please can anyone help?
I have managed to download the manual for the 33FD9944/01S but have been unable to find a free download for the FTR9964/12S receiver unit.

brian · « **Reply #11 on:** January 22, 2009,12:41:30 »

Hi,
Have you tried entering the sam mode of the box (not the panel)
and changing the "stand alone" option to yes?
The procedure for this can be found if you google "lumenlab" and enter FTR9964 in the search box and read the forum notes
Hope this helps
Bri

Mulja tv repair portal · « **Reply #11 on:** January 22, 2009,12:41:30 »

Mulja tv repair portal

News: