Author Topic: Toshiba 26C3030D no menu (Read 6913 times)

slimjimmy · « **on:** September 22, 2010,06:14:48 »

I have a toshiba 26C3030D, when it is first switched on the backlight is on but there is no menu or picture.
There is no response from remote or buttons on TV.
Any help would be much appreciated.

Thanks in advance.

Mulja tv repair portal · « **on:** September 22, 2010,06:14:48 »

sparky · « **Reply #1 on:** September 22, 2010,07:22:55 »

hi
it sounds like you need to change the eeprom chip
dave

slimjimmy · « **Reply #2 on:** September 22, 2010,08:24:26 »

Sorry, forgot to say if TV is left switched on eventually it will start working.

Mulja tv repair portal · « **Reply #2 on:** September 22, 2010,08:24:26 »

Turnip · « **Reply #3 on:** September 22, 2010,09:41:45 »

Hi,
Don't have this one listed - wonder what boards are fitted - Vestel/Beko/whatever.

Piccy would be nice - Chris.

brainstorm · « **Reply #4 on:** September 22, 2010,10:22:33 »

Hi,

Have you tried switching the set to analogue when it is in fault??

If the analogue works ok , then you probably need to reload the firmware

Brian

slimjimmy · « **Reply #5 on:** September 22, 2010,11:39:25 »

Can anybody email this firmware to me?

Mulja tv repair portal · « **Reply #5 on:** September 22, 2010,11:39:25 »

brainstorm · « **Reply #6 on:** September 23, 2010,04:14:28 »

Hi,

I don't have the firmware for the 26 inch, i have only the 32inch

Sorry

Brian

Turnip · « **Reply #7 on:** September 23, 2010,13:38:39 »

Hi, Bri,
Just a thought. If it works Ok after a while - why is firmware required ?

Ever ancient and ignorant - Is 'Firmware' EEprom re-programming stuff, or something rather more turgid - Very curious - Chris.

brainstorm · « **Reply #8 on:** September 24, 2010,08:12:21 »

Hi Chris,

Sorry, yes you are right, missed that bit!!

I have had the same thing with the 32inch where it was intermittent on the Freeview side, and it turned out to a dodgy plug on one of the plugs that plug into the freeview board.

I had to replace the lead, but you might find its no longer available, could try 'wiggling' to prove it when its in fault??

If it is the lead then try recrimping the connectors in the plug

Brian

Turnip · « **Reply #9 on:** September 25, 2010,12:08:23 »

Hi again Brian,

No-one has admitted knowing the actual maker, or supplied piccies, and as I have neither the 26 or 32 Tosh version listed, don't know whether to have a Beko into the Vestel file, or quite what - Chris.

Grizzly · « **Reply #10 on:** December 16, 2010,17:11:05 »

I have the same TV with exactly the same problem. I opened it up about 3 weeks ago and re-seated all the plugs and all was well... But... It's back... Gray screen, which eventually turns blue with no response from any controls!.. Does it really need to go to the Skip or does anybody have any bright ideas??

Contrast John · « **Reply #11 on:** December 17, 2010,14:54:52 »

Hi All
Had this problem a couple of times and its been a duff lcd panel. Usually it can be proved by holding the top corners of the screen and giving it a twist while the fault is present. If the picture returns you've found your problem.
Regards
John.

Turnip · « **Reply #12 on:** December 18, 2010,11:18:59 »

Nice one John,

Had it a while ago, but forgot - the twist showed the fault - pity as it became scrap - Chris.

Mulja tv repair portal · « **Reply #12 on:** December 18, 2010,11:18:59 »

Mulja tv repair portal

News: