Author Topic: ORION TV32RN10D need help set dead (Read 8834 times)

blackbox4498 · « **on:** November 25, 2011,05:25:11 »

--------------------------------------------------------------------------------
ORION TV32RN10D switched off as normal now it wont switch on i have 230 v at mains fuses ok checked for visual damage to components .all seam ok any help would be grateful.

Mulja tv repair portal · « **on:** November 25, 2011,05:25:11 »

Turnip · « **Reply #1 on:** November 25, 2011,06:09:12 »

Hi BB,

Have a note ( D424 duff and broken (H373) ) not seen one myself - Chris.

blackbox4498 · « **Reply #2 on:** November 27, 2011,06:48:04 »

checked d 424 reads ok i have 0v across main cap.

Mulja tv repair portal · « **Reply #2 on:** November 27, 2011,06:48:04 »

sparky · « **Reply #3 on:** November 27, 2011,07:14:56 »

hi
as fuse in plug gone or on pcb or break in mains lead
dave

Turnip · « **Reply #4 on:** November 27, 2011,07:38:16 »

Hi,

Found up a piccy - seems to be a relay near mains input, not sure about any PFC - Chris

E Parton · « **Reply #5 on:** November 27, 2011,09:15:10 »

...Not familliar with this pcb at all ..
but the presence of a relay might suggest a seperate standby supply to drive the relay ..
Don't suppose that the small wound component is a mini mains transformer to provide the standby supply ?
A bit simplistic ...but might be a possible ...
If not then trace backwards from the relay coil ..and look how the supply to its drive transistor is generated ..
Evan

Mulja tv repair portal · « **Reply #5 on:** November 27, 2011,09:15:10 »

sparky · « **Reply #6 on:** November 27, 2011,09:52:44 »

hi
take psu out look under the 2 chokes for dry joints
dave

Turnip · « **Reply #7 on:** November 27, 2011,10:39:34 »

Hi,

On second look think I see a S/by TX and drive chip mid RHS - any secondary S/by 5V and red led ? - Chris.

blackbox4498 · « **Reply #8 on:** December 06, 2011,07:31:05 »

not sure which chip you are refering to.

jimca007 · « **Reply #9 on:** December 06, 2011,08:19:05 »

funnily I havent had one of these for a while but they were going down right left and centre at one point. Save yourself a lot of grief and get a new replacement from flee-bay for 30 odd quid. As much as I'm all for repairing panels sometimes financially its just not worth it.

blackbox4498 · « **Reply #10 on:** December 06, 2011,14:05:17 »

Quote from: Turnip on November 27, 2011,07:38:16

Hi,

Found up a piccy - seems to be a relay near mains input, not sure about any PFC - Chris

cant see relay near mains input.

Turnip · « **Reply #11 on:** December 07, 2011,13:15:32 »

Hi BB,

Its the black rectangular thing RHS just above that large copper-wound component - can't be more specific as have never met one - Chris

blackbox4498 · « **Reply #12 on:** December 08, 2011,08:27:05 »

Quote from: Turnip on November 27, 2011,10:39:34

Hi,

On second look think I see a S/by TX and drive chip mid RHS - any secondary S/by 5V and red led ? - Chris.

i have 5v at stand by but no led`s.

Ohm Supplies · « **Reply #13 on:** December 08, 2011,11:50:20 »

The most common fault on these would be the following symptom:

. 5v stand by, relay click, nothing. You also get a 33v near the connections at the top.

However as you've 0v across the smoothing block, you must have a primary fault, i'd check from the bridge onwards

regards
Andy

Turnip · « **Reply #14 on:** December 08, 2011,12:34:52 »

Hi,
Wonder if the 5v S/by applied to the main board would help engage that relay to turn set on. No Red led points towards a main board prob - Chris

Mulja tv repair portal · « **Reply #14 on:** December 08, 2011,12:34:52 »

News:

Author Topic: ORION TV32RN10D need help set dead (Read 8834 times)

Mulja tv repair portal

Mulja tv repair portal

Mulja tv repair portal

Mulja tv repair portal