Author Topic: Onei 26av400 (Read 8104 times)

LEEDASH · « **on:** January 25, 2013,14:41:13 »

hi all,i have this lcd 'onei' lcd tv,which is faulty,which just flashes its standby light.Any one know what could be at fault ?

Mulja tv repair portal · « **on:** January 25, 2013,14:41:13 »

LEEDASH · « **Reply #1 on:** January 26, 2013,15:59:52 »

The vestel board number is 17pw26-4,if anyone has any info on this.

LEEDASH · « **Reply #2 on:** January 26, 2013,16:59:30 »

Mulja tv repair portal · « **Reply #2 on:** January 26, 2013,16:59:30 »

sparky · « **Reply #3 on:** January 27, 2013,04:15:22 »

have you checked anything yet
diodes etc

LEEDASH · « **Reply #4 on:** January 27, 2013,05:58:59 »

Not yet would like a bit of advice on where to start,

t1412 · « **Reply #5 on:** January 29, 2013,00:24:15 »

make sure when you start testing, either desolder one end of the resistor diode or take them out of the circuit, with capacitors and transistor it would be better to take them out good luck

regards
shaun

Mulja tv repair portal · « **Reply #5 on:** January 29, 2013,00:24:15 »

LEEDASH · « **Reply #6 on:** January 29, 2013,15:38:24 »

Has anyone had problems with these boards,i thought about changing the 'start up caps' c801 c892' one cap is 100uf 25v and the other is either a 3,3uf 50v 0r 33uf 50v,small writing on the cap ? can some one confirm which is right.

fix2003 · « **Reply #7 on:** January 30, 2013,02:39:33 »

c801 is 33u 50v

LEEDASH · « **Reply #8 on:** January 31, 2013,16:04:37 »

update,changed the two caps as last message i put up,no change,still getting flashing light and about 1 minute after the plug is pulled it still flashing ?
i wouldnt mind if someone has the info what cap does what,is this possible ?

WILLYAM1 · « **Reply #9 on:** February 01, 2013,10:18:00 »

hi.
check if any short regulaturs in main board or very small resistance.
hade a tv with same p.s and power led blue was flickring.
i found that the HDMI IC IS SHORT.

LEEDASH · « **Reply #10 on:** February 01, 2013,16:43:43 »

Tell me more ?

imran khan · « **Reply #11 on:** February 01, 2013,18:47:16 »

Check dry sold joints frist, Resold blast board H.V transformer and connectors come from power supply..

LEEDASH · « **Reply #12 on:** February 02, 2013,11:52:54 »

Cheers imran,so resolder the transformer(s) and maybe it may cure it ?

imran khan · « **Reply #13 on:** February 02, 2013,17:24:17 »

Mostly heated areas had dry solds
tip woks many times.
See also
http://techniforum.eu/viewtopic.php?f=7&t=31983&p=97650#p97650

LEEDASH · « **Reply #14 on:** February 02, 2013,17:41:39 »

cheers imran i will keep you posted

Mulja tv repair portal · « **Reply #14 on:** February 02, 2013,17:41:39 »

News:

Author Topic: Onei 26av400 (Read 8104 times)

Mulja tv repair portal

Mulja tv repair portal

Mulja tv repair portal

Mulja tv repair portal