Recent Posts

Pages: [1] 2 3 4 5 6 ... 10
1
LCD TV forum / Re: Is my TV goosed?
« Last post by Davy on September 13, 2024,15:22:26  »
Hi,
The black spot looks like screen damage, the others look the same too, as for the black spot I had something like that on a battery TV, dunno what it was it was in the panel, water, compression damage..... these things are usually on on of the corners.

Dave
2
LCD TV forum / Re: Philips 30pf9975 (Chassis FTL13EAA)
« Last post by downunder on July 17, 2024,23:23:31  »
HI Evan,
Your symptoms indicate that the OTC-supply may be coming on faster than the FBX-supply. At switch-on, the OTC is initialised along with all it's IC2 address to see which components are present. If the FBX is not present at this point due to a slow start, the OTC concludes there is no FBX and sends the set into protect.

A Philips service bulletin suggest the following mod:
On Aux power supply, replace positions 3031 and 3032 with a 27K 5W resistor. So you remove 3031 and 3032 and place this new resistor on posn
3028.
Replace 2002 with a 330u 25V elco and 2003 with a 680u 25V elco. Hope that helps,  Bruce

3
LCD TV forum / Re: PHILIPS 30PF9975/12
« Last post by nicam49 on July 17, 2024,18:27:45  »
Yes there is a service bulletin on this fault. Pm me for details
4
LCD TV forum / Re: Philips 30pf9975 (Chassis FTL13EAA)
« Last post by nicam49 on July 17, 2024,16:26:23  »
Hi, not sure if this is same fault, but for anyone searching this model, if you warm up the  back of the TV near the top and it starts up ok,  then there's a stock fault  that is fixed by changing the value of a resistor on the PSU board. Don't have details at hand, but will try to dig them out if you pm me.
5
LCD TV forum / Re: 17MB12-2 Dump
« Last post by IBRAHIMSAT on April 18, 2024,01:33:15  »
 :72:
Quote from: Mr Rage on April 16, 2010,08:39:21
Hi, i'm looking for a 17MB12-2 dump for a 26" (Bush IDLCD26TV27HD - although any 26" will do).

I'd appreciate any help, or alternative dump suggestions.

Thanks,

Rory
6
LCD TV forum / Re: vestel 17mb25 - "No Signal"
« Last post by risting on March 04, 2024,15:14:16  »
Please i need help for favorit tv motherboard is VESTEL 17MB60-3  i no have signal on channels digital analog too  like dead tuner
tv working in menu i have picture no have another problem  :sign0085:
7
LCD TV forum / Re: JVC LED TV backlight problem, Power board and LED ok! Please help!
« Last post by sinclairtv on February 01, 2024,06:53:59  »
It would be nice to know if tv was still working after replacing the backlights
8
LCD TV forum / Re: JVC LED TV backlight problem, Power board and LED ok! Please help!
« Last post by downunder on October 31, 2023,19:41:42  »

Excellent! yes, one tardy LED is enough to induce the problem. I reckon you've got it licked.
9
LCD TV forum / Re: JVC LED TV backlight problem, Power board and LED ok! Please help!
« Last post by metallicaz on October 31, 2023,07:43:37  »
Hi Bruce,

I replaced the Power board, but to my luck, the replacement P. board only lasted for two days, after which, it completely went out. This time, the red stand-by light also disappeared (this wasn't an issue with the original board). So, I re-installed the original power board for time being.

I replaced the old backlights with a new set. I did carry out a test on the old backlights, they were all working, but, one of the LED, even though, it lit-up, but had a few nano-second delay (nano second flickering). Let's see, if this new set of backlights resolve this issue, at least, now I can rule out the Power-board and the backlights.

Thank you for your reply and help. You have been very helpful!

10
LCD TV forum / Re: LG55EA980W
« Last post by downunder on October 30, 2023,19:28:11  »

I don't have the service manual for that model - doubt it would have the psu schematic anyway. Standby is mostly generated by a small 8 pin IC next to a small transformer, usually supplied by a small bridge rectifier connected permanently to the mains.                Bruce
Pages: [1] 2 3 4 5 6 ... 10
download